CCR1072-1G-8S+ is equipped with two redundant Hot Swap 12v 150W AC/DC power supplies – if one of them goes out of order, second one will take over.
Hot Swap 12v 150W AC/DC power supplies for CCR1072-1G-8S+ are now available for purchase separately. You can replace them on the go to ensure zero downtime, no need to even restart the router
The FTC is a simple Fiber to Copper converter. Unlike many other media converters available on market, it has outdoor waterproof case with lock screw, it’s mounting bracket can be attached and locked with a screw from inside the case. Unit has 12-57V PoE with 802.3af/at support (with unshielded cross cable). Comes with PoE injector and power supply. Works only with Gigabit SFP connections.
48 to 24V Gigabit PoE Converter
This device lets you use any 48V PoE source (including Passive PoE, Telecom PoE, 802.3af and 802.3at) to power RouterBOARD devices.
Simply plug any 48V PoE powered ethernet cable into one port, and any 8-30V capable RouterBOARD device into the other. This device is capable to provide high power output – up to 24W (up to 1A at 24V).
You can power it with virtually any 42-57V PoE solutions available on market today (Passive, Telecom, 802.3af and 802.3at PoE plus supported)
The device is a rugged metallic design, with high quality components and integrated heatsink design. The case also has mounting holes so you can attach it to a wall.
Ethernet shield pins are inside the Ethernet connectors, so that shielded ethernet can be used, to ground either at the converter itself, or at the devices at both ends. Supports 10/100/1000Mbps Ethernet.
Note: In case if 803.3af compilant PSE is used, total output power should not exceed 12.95w (limited by the 803.3af standard).
48V 1.46A Power Adapter + Power plug
High power 24V 1.6A power supply + power plug.
Recommended for long cable runs with several high power wireless cards
2.4-5.8GHz Swivel Antenna with cable and MMCX connector.
2.4-5.8GHz Swivel Antenna with cable and U.fl connector. Approximately 4dBi gain
The quickMOUNT pro LHG is a advanced wall or pole mount adapter for our new LHG antennas.
The quickMOUNT pro gives possibility to turn antenna within 140° both in horizontal and vertical plane. With the quickMOUNT pro
it is possible to perfectly set antenna alignment using integrated graduated scale.
The quickMOUNT extra is a advanced wall mount adapter for large point to point and sector antennas.
You can mount it on the wall or use it as an adapter from large diameter pole to small size antenna mounting clip ensuring reliable fitment. The quickMOUNT extra gives possibility to turn antenna within 190°.
With the quickMOUNT extra is compatible with our long range heavy antennas like 30dBi parabolic dish mANT 30 or 19dBi sector mANT 19s.
The quickMOUNT pro is an advanced wall mount adapter for small point to point and sector antennas. You can mount it on the wall or use it as an adapter from large diameter pole to small size antenna mounting clip ensuring reliable fitment.
The quickMOUNT pro gives possibility to turn antenna within 140° both in horizontal and vertical plane. With the quickMOUNT pro it is possible to perfectly set antenna alignment using integrated graduated scale.
You can use the quickMOUNT pro with any pole mountable device or MikroTik’s small mounting clip with weight less than 1.5 kg.
The adapter is very durable due to it’s special plastic composite material – anvilNITE (TM).
A super low loss 50cm long RPSMA cable for superior connection quality, suited for indoor and outdoor use, this cable provides superior matching and loss values.
The name of this cable comes from combining the words “flexible” and “waveguide”, to denote the high end features of this product.
The inner conductor is silver plated copper, and both connectors are soldered, not crimped, for the best possible signal quality. Ideally suited for our BaseBox and other products with RPSMA connectors, and works with most antennas.
24V 0.8A Power Supply
Fits all RouterBOARD models.